Difference between revisions of "Central sterile services department"

From The HILLSIDE
Jump to navigation Jump to search
Line 373: Line 373:
 
'''BEDS'''  
 
'''BEDS'''  
 
|'''SCANDINAVIA'''       
 
|'''SCANDINAVIA'''       
|   '''BELGIUM'''  
+
|'''BELGIUM'''  
 
|'''NETHERLANDS'''  
 
|'''NETHERLANDS'''  
|       '''RSA<sup>1</sup>'''  
+
|'''RSA<sup>1</sup>'''  
 
|-
 
|-
 
 
| colspan="3" |                               '''m² PER BED'''  
+
| colspan="3" |'''m² PER BED'''  
 
|
 
|
 
|-
 
|-
Line 418: Line 418:
 
|-
 
|-
 
 
| colspan="4" |                           '''TOTAL AREA'''  
+
| colspan="4" |'''TOTAL AREA'''  
 
|-
 
|-
 
|200 BEDS  
 
|200 BEDS  
Line 448: Line 448:
 
It is however; clear that the size of a CSSD cannot be generically determined on the basis of statistics or averages. Every CSSD has its own set of area determinants that need to be logically evaluated in order to arrive at an area that is the optimal combination of functionality and cost effectiveness.  
 
It is however; clear that the size of a CSSD cannot be generically determined on the basis of statistics or averages. Every CSSD has its own set of area determinants that need to be logically evaluated in order to arrive at an area that is the optimal combination of functionality and cost effectiveness.  
  
== Proportional allocation of space in a CSSD facility ==
+
==Proportional allocation of space in a CSSD facility==
 
Table 5: Space allocation in a CSSD (Putsep and Cowan,1983, p.9)
 
Table 5: Space allocation in a CSSD (Putsep and Cowan,1983, p.9)
 
{| class="wikitable"
 
{| class="wikitable"
Line 553: Line 553:
 
Table 6: Proportional space allocation - Generic layout (600M<sup>2</sup> gross area)
 
Table 6: Proportional space allocation - Generic layout (600M<sup>2</sup> gross area)
 
{| class="wikitable"
 
{| class="wikitable"
| colspan="5" |                                                   '''DIRTYCLEANSTERILE SUPPORT'''  
+
| colspan="5" |'''DIRTYCLEANSTERILE SUPPORT'''
 
|-
 
|-
 
|
 
|
|Area (m²)  
+
|Area (m²)
|Area (m²)  
+
|Area (m²)
|Area (m²)  
+
|Area (m²)
|Area (m²)  
+
|Area (m²)
 
|-
 
|-
 
|
 
|
Line 567: Line 567:
 
|
 
|
 
|-
 
|-
|WASTE DISPOSAL  
+
|WASTE DISPOSAL
|12  
+
|12
 
|
 
|
 
|
 
|
 
|
 
|
 
|-
 
|-
|SLUICE  
+
|SLUICE
|12  
+
|12
 
|
 
|
 
|
 
|
 
|
 
|
 
|-
 
|-
|RECEIVING & SORTING  
+
|RECEIVING & SORTING
|25  
+
|25
 
|
 
|
 
|
 
|
 
|
 
|
 
|-
 
|-
|TROLLEY WASH  
+
|TROLLEY WASH
|5  
+
|5
 
|
 
|
 
|
 
|
 
|
 
|
 
|-
 
|-
|TROLLEY HOLDING  
+
|TROLLEY HOLDING
|5  
+
|5
 
|
 
|
 
|
 
|
 
|
 
|
 
|-
 
|-
|STORE  
+
|STORE
|12  
+
|12
 
|
 
|
 
|
 
|
 
|
 
|
 
|-
 
|-
|PPE TO DECON AREA  
+
|PPE TO DECON AREA
|8  
+
|8
 
|
 
|
 
|
 
|
 
|
 
|
 
|-
 
|-
|DECONTAMINATION AREA  
+
|DECONTAMINATION AREA
|100  
+
|100
 
|
 
|
 
|
 
|
 
|
 
|
 
|-
 
|-
|PPE TO IAP AREA  
+
|PPE TO IAP AREA
 
|
 
|
|8  
+
|8
 
|
 
|
 
|
 
|
 
|-
 
|-
|STORE  
+
|STORE
 
|
 
|
|12  
+
|12
 
|
 
|
 
|
 
|
 
|-
 
|-
|TEXTILE AREA  
+
|TEXTILE AREA
 
|
 
|
|16  
+
|16
 
|
 
|
 
|
 
|
 
|-
 
|-
|INSPECTION & PACKING  
+
|INSPECTION & PACKING
 
|
 
|
|100  
+
|100
 
|
 
|
 
|
 
|
 
|-
 
|-
|STERILIZATION  
+
|STERILIZATION
 
|
 
|
|30  
+
|30
 
|
 
|
 
|
 
|
 
|-
 
|-
|DISPATCH  
+
|DISPATCH
 
|
 
|
 
|
 
|
|15  
+
|15
 
|
 
|
 
|-
 
|-
|STERILE STORE  
+
|STERILE STORE
 
|
 
|
 
|
 
|
|40  
+
|40
 
|
 
|
 
|-
 
|-
|COOLING  
+
|COOLING
 
|
 
|
 
|
 
|
|30  
+
|30
 
|
 
|
 
|-
 
|-
|STERILIZER PLANT ROOM  
+
|STERILIZER PLANT ROOM
 
|
 
|
 
|
 
|
 
|
 
|
|18  
+
|18
 
|-
 
|-
|OFFICE  
+
|OFFICE
 
|
 
|
 
|
 
|
 
|
 
|
|12  
+
|12
 
|-
 
|-
|KITCHENETTE  
+
|KITCHENETTE
 
|
 
|
 
|
 
|
 
|
 
|
|12  
+
|12
 
|-
 
|-
|STAFF REST ROOM  
+
|STAFF REST ROOM
 
|
 
|
 
|
 
|
 
|
 
|
|35  
+
|35
 
|-
 
|-
|FEMALE CHANGE  
+
|FEMALE CHANGE
 
|
 
|
 
|
 
|
 
|
 
|
|30  
+
|30
 
|-
 
|-
|MALE CHANGE  
+
|MALE CHANGE
 
|
 
|
 
|
 
|
 
|
 
|
|15  
+
|15
 
|-
 
|-
|CSSD CORRIDOR  
+
|CSSD CORRIDOR
 
|
 
|
 
|
 
|
 
|
 
|
|48  
+
|48
 
|-
 
|-
 
|
 
|
Line 712: Line 712:
 
|-
 
|-
 
|'''TOTAL AREA (SQ M)  '''  
 
|'''TOTAL AREA (SQ M)  '''  
|'''179'''  
+
|'''179'''
|'''166'''  
+
|'''166'''
|'''85'''  
+
|'''85'''
|'''170'''  
+
|'''170'''
 
|-
 
|-
 
|'''% OF TOTAL AREA  '''  
 
|'''% OF TOTAL AREA  '''  
|'''30%'''  
+
|'''30%'''
|'''28%'''  
+
|'''28%'''
|'''14%'''  
+
|'''14%'''
|'''28%'''  
+
|'''28%'''
 
|}
 
|}
 
Table 7: Proportional space allocation - Generic layout  without staff facilities (450M<sup>2</sup> gross area)
 
Table 7: Proportional space allocation - Generic layout  without staff facilities (450M<sup>2</sup> gross area)
 
{| class="wikitable"
 
{| class="wikitable"
| colspan="5" |                                                 '''DIRTY      CLEAN      STERILE  SUPPORT'''  
+
| colspan="5" |'''DIRTY      CLEAN      STERILE  SUPPORT'''
 
|-
 
|-
 
|
 
|
|Area (m²)  
+
|Area (m²)
|Area (m²)  
+
|Area (m²)
|Area (m²)  
+
|Area (m²)
|Area (m²)  
+
|Area (m²)
 
|-
 
|-
 
|
 
|
Line 739: Line 739:
 
|
 
|
 
|-
 
|-
|WASTE DISPOSAL  
+
|WASTE DISPOSAL
|12  
+
|12
 
|
 
|
 
|
 
|
 
|
 
|
 
|-
 
|-
|SLUICE  
+
|SLUICE
|12  
+
|12
 
|
 
|
 
|
 
|
 
|
 
|
 
|-
 
|-
|RECEIVING & SORTING  
+
|RECEIVING & SORTING
|25  
+
|25
 
|
 
|
 
|
 
|
 
|
 
|
 
|-
 
|-
|TROLLEY WASH  
+
|TROLLEY WASH
|5  
+
|5
 
|
 
|
 
|
 
|
 
|
 
|
 
|-
 
|-
|TROLLEY HOLDING  
+
|TROLLEY HOLDING
|5  
+
|5
 
|
 
|
 
|
 
|
 
|
 
|
 
|-
 
|-
|STORE  
+
|STORE
|12  
+
|12
 
|
 
|
 
|
 
|
 
|
 
|
 
|-
 
|-
|PPE TO DECON AREA  
+
|PPE TO DECON AREA
|8  
+
|8
 
|
 
|
 
|
 
|
 
|
 
|
 
|-
 
|-
|DECONTAMINATION AREA  
+
|DECONTAMINATION AREA
|100  
+
|100
 
|
 
|
 
|
 
|
 
|
 
|
 
|-
 
|-
|PPE TO IAP AREA  
+
|PPE TO IAP AREA
 
|
 
|
|8  
+
|8
 
|
 
|
 
|
 
|
 
|-
 
|-
|STORE  
+
|STORE
 
|
 
|
|12  
+
|12
 
|
 
|
 
|
 
|
 
|-
 
|-
|TEXTILE AREA  
+
|TEXTILE AREA
 
|
 
|
|16  
+
|16
 
|
 
|
 
|
 
|
 
|-
 
|-
|INSPECTION & PACKING  
+
|INSPECTION & PACKING
 
|
 
|
|100  
+
|100
 
|
 
|
 
|
 
|
 
|-
 
|-
|STERILIZATION  
+
|STERILIZATION
 
|
 
|
|30  
+
|30
 
|
 
|
 
|
 
|
 
|-
 
|-
|DISPATCH  
+
|DISPATCH
 
|
 
|
 
|
 
|
|15  
+
|15
 
|
 
|
 
|-
 
|-
|STERILE STORE  
+
|STERILE STORE
 
|
 
|
 
|
 
|
|40  
+
|40
 
|
 
|
 
|-
 
|-
|COOLING  
+
|COOLING
 
|
 
|
 
|
 
|
|30  
+
|30
 
|
 
|
 
|-
 
|-
|STERILIZER PLANT ROOM  
+
|STERILIZER PLANT ROOM
 
|
 
|
 
|
 
|
 
|
 
|
|18  
+
|18
 
|-
 
|-
|OFFICE  
+
|OFFICE
 
|
 
|
 
|
 
|
 
|
 
|
|12  
+
|12
 
|-
 
|-
 
|
 
|
Line 854: Line 854:
 
|-
 
|-
 
|'''TOTAL AREA (SQ M)  '''  
 
|'''TOTAL AREA (SQ M)  '''  
|'''179'''  
+
|'''179'''
|'''166'''  
+
|'''166'''
|'''85'''  
+
|'''85'''
|'''30'''  
+
|'''30'''
 
|-
 
|-
 
|'''% OF TOTAL AREA  '''  
 
|'''% OF TOTAL AREA  '''  
|'''39%'''  
+
|'''39%'''
|'''36%'''  
+
|'''36%'''
|'''18%'''  
+
|'''18%'''
|'''7%'''  
+
|'''7%'''
 
|}
 
|}
  
== Typical Floor Layouts ==
+
==Typical Floor Layouts==
 
The following generic plans are included to illustrate the combined effect of gross floor area allocation, proportional space allocation, and work-flow requirements.  
 
The following generic plans are included to illustrate the combined effect of gross floor area allocation, proportional space allocation, and work-flow requirements.  
  
Line 912: Line 912:
 
|}
 
|}
  
= Individual Space Requirements =
+
=Individual Space Requirements=
  
== CSSD Layout  Unpacked ==
+
==CSSD Layout  Unpacked==
 
Due to the uni-directional sequential nature of the work flow in the CSSD, activities are interrelated and inter-dependent. It is, therefore, critical to the functional efficiency and safety of the CSSD that those areas are sequentially linked for uni-directional flow-through of instrumentation, with no room for back tracking.  
 
Due to the uni-directional sequential nature of the work flow in the CSSD, activities are interrelated and inter-dependent. It is, therefore, critical to the functional efficiency and safety of the CSSD that those areas are sequentially linked for uni-directional flow-through of instrumentation, with no room for back tracking.  
  
Line 921: Line 921:
 
Drawing 4: A generic layout to illustrate  room layouts
 
Drawing 4: A generic layout to illustrate  room layouts
  
== Receiving and Sorting ==
+
==Receiving and Sorting==
  
=== Function  ===
+
===Function  ===
 
This is the area where all soiled articles for reprocessing are received on trolleys from the main corridor from user departments throughout the hospital.  
 
This is the area where all soiled articles for reprocessing are received on trolleys from the main corridor from user departments throughout the hospital.  
  
=== Location and Relationship  ===
+
===Location and Relationship  ===
  
* Close to main entry doors to the CSSD unit  
+
*Close to main entry doors to the CSSD unit  
  
* Visual access to main entry.  
+
*Visual access to main entry.  
  
 
Drawing 5: Receiving and sorting
 
Drawing 5: Receiving and sorting
  
=== Activities  ===
+
===Activities  ===
  
* Access for deliveries of supplies, return of contaminated goods and the collection of waste and contaminated linen  
+
*Access for deliveries of supplies, return of contaminated goods and the collection of waste and contaminated linen  
* Contaminated articles are received at a counter with a trolley hatch, where the articles are logged, sorted and forwarded to the decontamination area  
+
*Contaminated articles are received at a counter with a trolley hatch, where the articles are logged, sorted and forwarded to the decontamination area  
  
* Contaminated linen is put into linen bags and stored in the waste-disposal store for transport to the laundry  
+
*Contaminated linen is put into linen bags and stored in the waste-disposal store for transport to the laundry  
* Supplies are received in the supplies store where they are opened and packaging is discarded in the waste-disposal store    
+
*Supplies are received in the supplies store where they are opened and packaging is discarded in the waste-disposal store  
* Trolleys are sent to the trolley wash bay.  
+
*Trolleys are sent to the trolley wash bay.  
  
=== Requirements  ===
+
===Requirements  ===
  
* Visual access to entrance doors  
+
*Visual access to entrance doors  
  
* All entrances should be secure and controlled by means of communication to prevent access by unauthorised people  
+
*All entrances should be secure and controlled by means of communication to prevent access by unauthorised people  
* A glass partition with lockable sliding hatch between this area and the corridor • A lockable hatch for trolleys  
+
*A glass partition with lockable sliding hatch between this area and the corridor • A lockable hatch for trolleys  
* The red-line principle is applicable at the receiving area; only material and trolleys are to enter the CSSD via this entrance • Worktop for unpacking and sorting  
+
*The red-line principle is applicable at the receiving area; only material and trolleys are to enter the CSSD via this entrance • Worktop for unpacking and sorting  
* Hand-washing facilities.  
+
*Hand-washing facilities.  
  
=== Fixtures, fittings and equipment  ===
+
===Fixtures, fittings and equipment  ===
  
* Receiving counter with pass-through hatch and trolley hatch, acting as red line  
+
*Receiving counter with pass-through hatch and trolley hatch, acting as red line  
* Sorting work tables – standing height    
+
*Sorting work tables – standing height  
* Clinical hand-wash basin, complete with liquid soap dispenser and paper-towel dispenser • Space should be allowed for record-keeping and record-keeping supplies.  
+
*Clinical hand-wash basin, complete with liquid soap dispenser and paper-towel dispenser • Space should be allowed for record-keeping and record-keeping supplies.  
  
 
Photograph 7: Trolley pass-through hatch (Tygerberg hospital)
 
Photograph 7: Trolley pass-through hatch (Tygerberg hospital)
  
=== Services  ===
+
===Services  ===
  
* 2 x telephones  
+
*2 x telephones  
* 2 x data points  
+
*2 x data points  
* CSSD technician call system  
+
*CSSD technician call system  
* Power outlets for computer points, computer, fax and printer  
+
*Power outlets for computer points, computer, fax and printer  
  
* Access control to outside door.
+
*Access control to outside door.
  
== Waste Disposal ==
+
==Waste Disposal==
 
'''Function'''  
 
'''Function'''  
  
 
Contaminated waste articles are stored for collection and transport to the respective disposal areas.  
 
Contaminated waste articles are stored for collection and transport to the respective disposal areas.  
  
=== Location and relationship ===
+
===Location and relationship===
 
Attached to the receiving area.  
 
Attached to the receiving area.  
  
 
Drawing 6: Waste disposal
 
Drawing 6: Waste disposal
  
=== Activities  ===
+
===Activities  ===
  
* The sluice area and waste-disposal area could be combined in smaller units  
+
*The sluice area and waste-disposal area could be combined in smaller units  
* Contaminated waste articles are temporarily stored for collection and transport to the respective disposal areas  
+
*Contaminated waste articles are temporarily stored for collection and transport to the respective disposal areas  
  
* Contaminated linen is temporarily stored in canvas bags for collection and transport to the laundry  
+
*Contaminated linen is temporarily stored in canvas bags for collection and transport to the laundry  
* Third-party collection area (depot).    
+
*Third-party collection area (depot).  
  
 
Categories of waste stored in the waste-disposal area could include:  
 
Categories of waste stored in the waste-disposal area could include:  
  
* Health-care waste, infectious waste, sharps  
+
*Health-care waste, infectious waste, sharps  
* General office waste  
+
*General office waste  
  
* Packaging and cartons from bulk supplies stored in the unit • Linen bags used to collect reusable items  
+
*Packaging and cartons from bulk supplies stored in the unit • Linen bags used to collect reusable items  
* Sharps from theatres.  
+
*Sharps from theatres.  
  
=== Requirements  ===
+
===Requirements  ===
  
* An independent secure area for temporary storage of clinical waste awaiting collection in accordance with local waste management policy  
+
*An independent secure area for temporary storage of clinical waste awaiting collection in accordance with local waste management policy  
* The door to the receiving/sorting area side should be lockable from the CSSD side to prevent unauthorised entry  
+
*The door to the receiving/sorting area side should be lockable from the CSSD side to prevent unauthorised entry  
  
* Room layout should allow for easy recycling/re-use/disposal policy  
+
*Room layout should allow for easy recycling/re-use/disposal policy  
* Space for linen bags and waste containers  
+
*Space for linen bags and waste containers  
* An impermeable, hard-wearing floor with good drainage; it should be easy to clean and to disinfect, with an accessible water supply for cleaning purposes  
+
*An impermeable, hard-wearing floor with good drainage; it should be easy to clean and to disinfect, with an accessible water supply for cleaning purposes  
* The area should be protected from outside elements, inaccessible to animals, insects or birds and not situated in close proximity to fresh food stores, food preparation areas or patient waiting areas  
+
*The area should be protected from outside elements, inaccessible to animals, insects or birds and not situated in close proximity to fresh food stores, food preparation areas or patient waiting areas  
* It should be sized according to the volume of waste generated by the facility as well as the frequency of collection.  
+
*It should be sized according to the volume of waste generated by the facility as well as the frequency of collection.  
  
* A bumper rail to protect the wall behind the trolleys • Containers according to waste policy.
+
*A bumper rail to protect the wall behind the trolleys • Containers according to waste policy.
  
 
Photograph 8: Soiled-Linen trolleys
 
Photograph 8: Soiled-Linen trolleys
Line 1,012: Line 1,012:
 
Photograph 9: Infectious-waste and sharps-disposal containers
 
Photograph 9: Infectious-waste and sharps-disposal containers
  
=== '''Fixtures, fittings and equipment '' ''''' ===
+
==='''Fixtures, fittings and equipment '' '''''===
 
• Clinical hand-wash basin, complete with liquid-soap dispenser and paper-towel dispenser.  
 
• Clinical hand-wash basin, complete with liquid-soap dispenser and paper-towel dispenser.  
  
== Sluice ==
+
==Sluice==
 +
 
 +
==='''Function'''  ===
 +
Heavily soiled items are rinsed and waste items are discarded in suitable containers.  
 +
 
 +
=== Location and relationship  ===
 +
Drawing 7: Sluice area
 +
 
 +
=== Activities  ===
 +
 
 +
* Cleaning of heavily soiled items  
 +
 
 +
* Storing and cleaning of domestic cleaning equipment and holders (buckets, etc.).  
 +
 
 +
=== Requirements  ===
 +
 
 +
* Some lumens may require irrigating with a high pressure water-jet spray gun  
 +
* Heavily soiled instruments should be pre-rinsed using a submerged high-pressure water gun in a sluice area.  
 +
 
 +
=== Fixtures, fittings and equipment  ===
 +
 
 +
* Above-sink storage facilities for cleaning material and equipment  
 +
* Sluice unit  
 +
* Bucket sink  
 +
* Mop/broom rail.  
 +
 
 +
Photograph 10: High-pressure water gun 
 +
 
 +
Photograph 11: Drip sink with hinged bucket gridPhotograph 12: Double-bowl sink unit
 +
 
 +
== Trolley wash and storage ==
 +
 
 +
=== Function  ===
 +
Area for washing, disinfecting and storing of trolleys.  
 +
 
 +
=== Location and relationship  ===
 +
Drawing 8: Trolley wash and storage
 +
 
 +
=== Activities  ===
 +
 
 +
* This area receives returned contaminated trolleys from the decontamination area  
 +
* Trolleys are washed and cleaned before being moved through a trolley hatch to the holding bay  
 +
* Washed trolleys are temporarily stored in the holding bay until required.  
 +
 
 +
=== Requirements  ===
 +
 
 +
* Trolleys must be transferred via a trolley hatch to prevent entry  
 +
 
 +
* The floor in the washing bay needs to have a gradient and floor drain, as well as hosing facilities  
 +
* Trolley-washing facilities with adequate drainage.  
 +
 
 +
=== Fixtures, fittings and equipment  ===
 +
 
 +
* Trolley pass-through hatch  
 +
* Stainless steel sink • Water hose with hand-spray.  
 +
 
 +
Photograph 13: Trolley pass-through hatch (Tygerberg hospital)Photograph 14: Trolley cleaning (Tygerberg hospital)
 +
 
 +
=== Services  ===
 +
 
 +
* Cold water for water hose  
 +
* Floor drain in vicinity of wash stations and equipment loading/unloading areas.  
 +
 
 +
== Decontamination Area ==
 +
 
 +
=== Function  ===
 +
This area is used to sort instruments followed by manual or automated cleaning.  
 +
 
 +
Soiled instruments are placed in a pass through washer disinfector that will deliver clean instrumentation to the IAP Area. Selected items may be manually cleaned, because they are either too delicate or will not fit into the washer disinfector, then forwarded to the clean area via a pass-through hatch.  
 +
 
 +
Drawing 9: Automated cleaning area
 +
 
 +
=== Activities  ===
 +
 
 +
* Selective manual cleaning of instruments and equipment not suitable for automated cleaning.  
 +
* Disassembly and inspecting of contaminated returns  
 +
 
 +
* Rinsing of instruments and equipment  
 +
* Sorting and loading of medical instruments and equipment into trays/washer-disinfectors and other automated cleaning equipment.  
 +
 
 +
=== Requirements  ===
 +
 
 +
* Sufficient wall-mounted brackets for cleaning chemicals and brushes  
 +
* Sealed closed windows to the outside would be desirable  
 +
 
 +
* Space to park trolleys is essential  
 +
* Automated double-sided washer-disinfectors and ultrasonic cleaners are required for cleaning and drying of all suitable instruments and equipment. A minimum of two washing units should be provided to allow for maintenance and down-time  
 +
* Transfer hatch with sliding opening section (upwards or sideways) for the transfer of handwashed items and return of emptied disinfector trays  
 +
* The decontamination area has to be divided with a hard barrier from the IAP area, in order to prevent contaminated particles from freely entering the relatively cleaner IAP area. This barrier could be a solid brick wall or washer-disinfectors with panelling. A glass partitioning will contribute to an open-plan environment  
 +
* Adequate space should be allowed for trolleys to be manoeuvred without interfering with the work stations  
 +
 
 +
* The distance between tables should be about 1.5m and between a table and the wall not less than 1,2m.  
 +
 
 +
=== Fixtures, fittings and equipment   ===
 +
 
 +
* Stainless steel standing-height sorting tables with high-level shelves  
 +
* Ultrasonic cleaner, according to service requirements  
 +
* Washer-disinfectors with a drying cycle for instruments and tubing, according to service requirements  
 +
 
 +
* De-ionised, distilled, or reverse osmosis (RO) water for final rinsing is preferable  
 +
* Drying rack - work space must be available for drying manually cleaned instruments  
 +
* Double-bowl stainless steel pot-wash type sink with draining boards on both sides  
 +
* Tubing manifolds (air and water) and additional water outlets for water pistols  
 +
* A 1000mm-long flexible hose with a tapered-nozzle water pistol for cleaning narrow-bore tubes should be fitted over the space between the bowls  
 +
 
 +
* All taps to sinks should have threaded nozzles to allow for the fitting of a variety of cleaning gadgets  
 +
* Compressed-air outlets and pressure guns are required at all cleaning sinks  
 +
* Clinical hand-wash basin, complete with liquid-soap dispenser and paper-towel dispenser  
 +
* Wall-mounted cartridge soap dispenser  
 +
* Eye wash and first aid area  
 +
 
 +
* Automated washer disinfectors with a choice of racks for respiratory equipment washer, bowls, basins, containers, etc.  
 +
* Transfer trolleys  
 +
* Waste container for non-regulated waste and sharps  
 +
* One height-adjustable chair per table  
 +
* A silent clock • Storage shelving.  
 +
 
 +
Photograph 15: Washer/disinfectors (Tygerberg hospital)Photograph 16: Washer/disinfectors trays returned to the decontamination area via pass-through hatch(Tygerberg hospital)
 +
 
 +
Photograph 17: Pass-through between decontamination and IAP areas (Tygerberg hospital)
 +
 
 +
=== Services  ===
 +
 
 +
* Services to automated disinfectors as per manufacturers’ specifications  
 +
* Floor drains  
 +
* Trap for equipment drainage.  
 +
 
 +
== Raw materials and chemicals store ==
 +
 
 +
=== '''Function'''  ===
 +
Storage of consumables, raw goods and materials, and chemicals used in the decontaminated area.  
 +
 
 +
=== '''Location and relationship  ''' ===
 +
Drawing 10: Raw materials and chemicals store
 +
 
 +
=== '''Activities '' ''''' ===
 +
 
 +
* Receiving and storing of raw materials and consumables  
 +
* Distribution of goods to process areas  
 +
* Facilitating the disposal of transport packaging  
 +
 
 +
* Storage of consumables, raw goods and materials, and chemicals used in the decontaminated area.  
 +
 
 +
=== Requirements  ===
 +
 
 +
* Lockable transfer hatch on top of a worktop between this area and the department corridor  
 +
* Suitable slatted shelving for the range of consumables and chemicals that are stored in this room • Space for receipt, quarantine, inspection and acceptance of materials  
 +
* The store should be lockable.  
 +
 
 +
=== Fixtures, fittings and equipment  ===
 +
 
 +
* Slatted shelving  
 +
* Transfer hatch.  
 +
 
 +
== PPE Area - Gowning (to contaminated area) ==
 +
 
 +
=== Function  ===
 +
The PPE (personal protective equipment - gowning) room provides the only access to and from the decontamination area for staff, after putting on the appropriate PPE over garments and footwear.  
 +
 
 +
=== Location and relationship  ===
 +
The PPE room is the only human entry/exit point between the decontamination area and the CSSD departmental corridor.  
 +
 
 +
Drawing 11: PPE Gowning area
 +
 
 +
=== Activities  ===
 +
 
 +
* The PPE gowning room provides the only access to and from the decontamination area for staff.  
 +
* Facilities are provided for the storage and dispensing of personal protective equipment (PPE) over garments and footwear suitable for the decontamination-room activities  
 +
* It provides facilities for hand-washing before/after activities in the decontamination area  
 +
 
 +
* The PPE area serves as transfer point into/out of the red-line area.  
 +
 
 +
=== Requirements  ===
 +
 
 +
* PPE dispensers.  
 +
* Red-line demarcation barrier, with step-over wall  
 +
* There should be vision panels in doors and walls.  
 +
 
 +
=== Fixtures, fittings and equipment  ===
 +
 
 +
* Shelving for PPE dispensers  
 +
* Footwear and over-garment storage  
 +
* Waste containers – either foot-operated or wall-mounted  
 +
* Clinical hand-wash basin complete with liquid-soap dispenser, paper \-towel dispenser, and mirror.  
 +
 
 +
== Inspection and packing area (IAP Area) ==
 +
 
 +
=== '''Function'''  ===
 +
Decontaminated instruments, equipment and other articles are inspected and packed here.  
 +
 
 +
=== Location and relationship  ===
 +
The IAP area must be divided by a hard barrier from the decontamination area, in order to prevent crosscontamination. This barrier could be a solid brick wall or built in washer-disinfector with panelling, but a glass wall will contribute to an open-plan environment.
 +
 
 +
Drawing 12: Inspection and packing area
 +
 
 +
=== Activities  ===
 +
 
 +
* Inspecting, functionality testing, assembling and packing cleaned and disinfected medical devices and accessories, according to predetermined required standards, in preparation for sterilisation  
 +
 
 +
* Packs are checked, reassembled, double-wrapped, labelled, dated, and signed on the checklist by the packer  
 +
* Delivering items to the steriliser loading area • Returning racks to the decontamination area.  
 +
 
 +
=== Requirements  ===
 +
 
 +
* Sufficient wall-mounted brackets for equipment  
 +
* Sealed closed windows to the outside would be desirable  
 +
* Space to park trolleys is essential  
 +
* Automated double-sided washer-disinfectors and ultrasonic cleaners are required  
 +
* Transfer hatch with sliding opening section (upwards or sideways) for the transfer of manually cleaned items, and return of empty washer racks  
 +
 
 +
* The IAP area must be divided by a hard barrier from the decontamination area, in order to prevent cross-contamination  
 +
* Adequate space should be allowed for trolleys to manoeuvre without interfering with the work stations  
 +
* The distance between tables should be about 1.5m, and that between a table and the wall not less than 1.2m  
 +
* Packing tables require power and ICT connections for use with computers and instrument scanners  
 +
* Space for mobile shelving units containing the items awaiting packaging.  
 +
 
 +
* Sterilisation wrap storage space/rack  
 +
* Hand rub station  
 +
* Clean environment with good lighting for inspections • There should be vision panels in doors and walls.  
 +
 
 +
Photograph 18: Visual-inspection of a device set following a cleaning process
 +
 
 +
=== Fixtures, fittings and equipment  ===
 +
 
 +
* Packing table(s) 2000mm x 700mm, by 800mm high, with a shelf below its surface and a basket rack above it  
 +
* Stainless-steel worktop space for a variety of activities  
 +
* Stainless-steel storage for raw materials  
 +
* High level storage for tray checklists  
 +
 
 +
* Mobile, height-adjustable chairs/stools • Table mounted lighted magnifiers • Hand rub station.  
 +
 
 +
Photograph 19: Textile folding tables (Tygerberg hospital)Photograph 20: Stainless steel worktop (Tygerberg hospital)
 +
 
 +
=== Services  ===
 +
 
 +
* Sufficient plug points for power to equipment on the packing tables should be ceiling-suspended  
 +
* Medical-grade compressed air.  
 +
 
 +
== Raw materials store for IAP Area ==
 +
 
 +
=== Function  ===
 +
Storing of materials used for processing in the clean side of the CSSD.  
 +
 
 +
=== Location and relationship   ===
 +
Drawing 13: Raw materials store for IAP area
 +
 
 +
=== '''Activities'''  ===
 +
Storing of materials used for processing in the clean side of the CSSD.  
 +
 
 +
=== Requirements  ===
 +
Lockable transfer hatch on top of a worktop between this area and the department corridor.  
 +
 
 +
Suitable slatted shelving for the range of consumables and chemicals that are stored in this room.  
 +
 
 +
=== Fixtures, fittings and equipment  ===
 +
 
 +
* Slatted shelving  
 +
 
 +
* Transfer hatch.  
 +
 
 +
== Textile room ==
  
 
=== '''Function'''  ===
 
=== '''Function'''  ===
Heavily soiled items are rinsed and waste items are discarded in suitable containers.  
+
Receiving, folding, packing, and storing of textile materials.  
 +
 
 +
=== Location and relationship  ===
 +
The textile room should be in close proximity to the IAP area, but also have a hatch to the CSSD departmental corridor to receive deliveries from the laundry.
 +
 
 +
Drawing 14: Textile room
 +
 
 +
=== Activities  ===
 +
 
 +
* Due to linting, linen MUST be folded in a separate room with its own air-conditioning.  
 +
* Once laundered, ironed, checked and folded, clean unwrapped textiles should be handled as little as possible and be placed in a positive-pressure, temperature-controlled, and properly ventilated area with limited access in order to prevent accumulation of dust and lint.  
 +
 
 +
=== Requirements  ===
 +
 
 +
* Receiving hatch to departmental corridor side  
 +
* The area used for the textile preparation should be physically separated from all other areas  
 +
 
 +
* The ventilation system should be designed so that air flows into the textile preparation area (via negative pressure)  
 +
* The air flow should be of a down-draft type, and the number of air exchanges per hour should be sufficient to minimise lint particles in the air  
 +
* Vision panels in doors and walls.  
 +
 
 +
=== Fixtures, fittings and equipment  ===
 +
 
 +
* Clinical hand-wash basin, complete with liquid-soap dispenser and paper-towel dispenser  
 +
 
 +
* An illuminated linen inspection and folding table, 1800mm x 1250mm by 800mm high, with a foot switch to operate the light only during inspection. An acid-etched glass with the etched surface facing inwards would reduce the glare  
 +
* Shelving  
 +
* Stainless steel standing-height processing tables • Pass-through window.  
 +
 
 +
 Photograph 21: Textile folding table
 +
 
 +
=== '''Building services'''  ===
 +
Extraction with lint filter.  
 +
 
 +
== PPE Gowning area (to clean area) ==
 +
 
 +
=== Function  ===
 +
The PPE (gowning) room provides the only access to and from the decontamination area for staff, after putting on the appropriate PPE (personal protective equipment - over garments and footwear).
 +
 
 +
=== Location and relationship  ===
 +
The PPE room is the only human entry/exit point between the clean/IAP/steriliser/sterile storage area and the CSSD departmental corridor.  
 +
 
 +
Drawing 15: PPE Gowning area (IAP area)
 +
 
 +
=== Activities  ===
 +
 
 +
* The PPE (gowning) room provides the only access to and from the clean/IAP/steriliser/sterile storage area for staff  
 +
* Facilities are provided for the storage and dispensing of PPE (personal protective equipment - over garments and footwear) suitable for the decontamination room activities  
 +
* The room provides facilities for hand decontamination before/after activities in the clean (IAP) area  
 +
* It serves as transfer point into/out of the red-line area.  
 +
 
 +
=== Requirements  ===
 +
 
 +
* PPE dispensers.  
 +
* Red-line demarcation barrier, with step-over wall  
 +
* There should be vision panels in doors and walls.  
 +
 
 +
=== Fixtures, fittings and equipment  ===
 +
 
 +
* Shelving for PPE dispensers  
 +
 
 +
* Footwear and over-garment storage  
 +
* Waste containers – either foot operated, or wall-mounted  
 +
* Clinical hand-wash basin, complete with liquid-soap dispenser, paper-towel dispenser and mirror.  
 +
 
 +
=== Function  ===
 +
Area where loading trolleys are parked, sterilisers are loaded, sterilisation cycles are run, sterilisers are unloaded, sterilised packs are cooled, following completion of the sterilisation cycle. The size of the area will be dependent on the number and type of sterilisers installed and whether single- or double-door.
 +
 
 +
=== Location and relationship  ===
 +
 
 +
* This area is the transition from clean to sterile area  
 +
 
 +
* The sterilisation area should be adjacent to the preparation and packaging area.  
 +
 
 +
Drawing 16: Sterilisation area
 +
 
 +
=== Activities  ===
 +
 
 +
* Receiving packaged products from IAP  
 +
 
 +
* A holding area for loaded and empty sterilisation trolleys  
 +
* Loading sterilisers  
 +
* Unloading single-door sterilisers  
 +
* Facilitating validation and routine testing of sterilisers  
 +
* Cooling of sterilised goods  
 +
 
 +
* Where single-door autoclaves are installed, the autoclaves will be loaded and unloaded in the same area  
 +
* Where double-door autoclaves are installed, the unloading area is separate from the loading area  
 +
* In both cases, a separate cooling area from the loading area is required.  
 +
 
 +
=== Requirements  ===
 +
 
 +
* Sufficient sterilisers to meet hospital needs  
 +
 
 +
* Preferably sterilisers should be located in a restricted access area  
 +
* Autoclaves should ''not'' be located in high-traffic areas or near any potential sources of contamination, wash sinks, or containers for the disposal of linen and trash  
 +
* Material should flow from the preparation and packaging area to the sterilisation area and then on to sterile storage or distribution  
 +
* The ventilation system should be designed so that air flows out of the sterilisation area (via positive pressure)  
 +
* Circulation space for the free and unhindered manoeuvring, loading and unloading of steriliser trolleys  
 +
 
 +
* Exhaust over the front of the steriliser doors to extract heat and steam, in order not to compromise the HVAC air flow and temperature. An extraction system which is activated by the autoclave door opening rather than a constant extraction system should be considered  
 +
* It is generally advisable to install two smaller autoclaves rather than one large one  
 +
* An extra autoclave should be provided to cater for exceptional demand, maintenance and breakdown  
 +
* A clear space of 2m in front of the autoclave is needed to facilitate the handling of loading trolleys  
 +
* No partition wall should be closer than 750mm to any autoclave  
 +
 
 +
* The autoclaves must be well insulated. The emission of heat to the environment must be minimal, and adequate extraction facilities should be provided to remove hot air and steam from the autoclave at a rate equivalent to 15 air changes per hour  
 +
* Require separate installation and accommodation according to manufacturer's recommendations  
 +
* The size of the area will be dependent on the number and type of sterilisers installed and, importantly, whether the sterilisers are single- or double-sided  
 +
* A duct enclosure can also minimise heat build-up within the workroom. An exhaust over the front of the steriliser(s) should be considered, to extract both heat (cabinet) and steam (opening door).  
 +
 
 +
=== Fixtures, Fittings and Equipment  ===
 +
• Adequate space should be allowed for sterilisers and aerators; loading, cooling of autoclave racks, storage of long, heat-resistant gloves • Autoclave cleaning supplies.  
 +
 
 +
Photograph 22: Autoclave trolley ready for loading (Tygerberg hospital)
 +
 
 +
== Cooling Area ==
 +
 
 +
=== Description and function  ===
 +
This area is used for the cooling of sterilised items on trolleys after being removed from the sterilisers.  
 +
 
 +
The size of the area will be dependent on the number and type of sterilisers installed.  
 +
 
 +
=== Location and relationship  ===
 +
This area is directly adjacent to the sterilisation area. Sterile items are temporarily stored here until cooled.
 +
 
 +
Drawing 17: Cooling Area
 +
 
 +
=== Activities  ===
 +
 
 +
* Cooling of sterilised items  
 +
* Transferring cooled items to storage.  
 +
 
 +
=== Requirements  ===
 +
 
 +
* Sufficient space for trolleys to stand and manoeuvre until they have been cooled and inspected • This should be a clear open space with sufficient room to manoeuvre sterilising trolleys  
 +
* Demarcated bay – floor marking.  
 +
 
 +
== Sterile Stores ==
 +
 
 +
=== '''Description and function'''  ===
 +
A dedicated sterile storage and dispatch area.  
 +
 
 +
=== Location and relationship  ===
 +
The sterile storage area should be located adjacent to the sterilisation area preferably in a separate, controlled, enclosed, limited-access area, the only function of which is to store sterile supplies.  
 +
 
 +
Drawing 18: Sterile pack store
 +
 
 +
=== '''Activities'''  ===
 +
Storing of sterile packs.  
 +
 
 +
=== Requirements  ===
 +
 
 +
* Supply air pressure should be positive with respect to surrounding areas and the level of filtration should be equal to that in an operating theatre  
 +
* There should be vision panels in doors and walls  
 +
* Area to be protected from direct sunlight  
 +
* Adequate and appropriate stainless steel slatted shelving in a clean environment  
 +
* Adequate and appropriate mobile storage systems and trolleys.  
 +
 
 +
=== Fixtures, fittings and equipment  ===
 +
 
 +
* Closed or covered mobile storage systems are preferable for high-traffic areas  
 +
* Open or wire shelving is suitable for confined storage areas, provided that proper attention is given to traffic control, area ventilation, and housekeeping  
 +
* Hand rub station.  
 +
 
 +
== Dispatch Desk ==
 +
 
 +
=== Function  ===
 +
Distribution of sterile items to the various user departments.  
 +
 
 +
Drawing 19: Dispatch desk
 +
 
 +
=== Activities  ===
 +
 
 +
* Dispatch of sterile items to the theatres and wards • Loading of sterile articles on trolleys  
 +
* Logging of dispatched deliveries.  
 +
 
 +
=== Requirements  ===
 +
 
 +
* Counter with service hatch and trolley pass-through hatch  
 +
* Red-line principle is applicable  
 +
 
 +
* No general access is allowed into the sterile storage and dispatch area.  
 +
 
 +
=== Fixtures, fittings and equipment  ===
 +
 
 +
* Trolley pass-through hatch and counter hatch  
 +
* Clinical hand-wash basin, complete with liquid-soap dispenser and paper-towel dispenser  
 +
* Stainless steel shelving  
 +
 
 +
* Filing cabinet  
 +
* Desk  
 +
* Chair  
 +
* Telephone  
 +
* Work surface  
 +
 
 +
* Hand rub station.  
 +
 
 +
== Office ==
 +
 
 +
=== '''Function'''  ===
 +
A space for administration/management.  
 +
 
 +
=== Location and relationship  ===
 +
Drawing 20: Office
 +
 
 +
=== Activities  ===
 +
 
 +
* Making and receiving phone calls  
 +
* Writing reports  
 +
* Access and printing data from computer  
 +
 
 +
* Unit management  
 +
* Shift handover meetings  
 +
* Staff management  
 +
* Record keeping and storage.  
 +
 
 +
=== Requirements  ===
 +
 
 +
* The office should be lockable  
 +
* No direct access from this area to the work areas is allowed. This area can also have a hatch link to the main hospital passage so that suppliers can interact with the unit manager without coming into the unit. This would be an infection risk.  
 +
 
 +
=== '''Fixtures, fittings and equipment  ''' ===
 +
 
 +
* Desk/sitting-height worktop  
 +
* Pinning board  
 +
* Whiteboard with marker tray  
 +
 
 +
* Blinds for privacy  
 +
 
 +
* Chairs  
 +
* Filing cabinet
 +
* Shelving  
 +
* Filing cabinet
 +
* Stationery cupboard.  
 +
 
 +
=== Services  ===
 +
 
 +
* IT and data connections  
 +
 
 +
* Electrical points • Telephone point.  
 +
 
 +
== Kitchenette ==
 +
 
 +
=== '''Function'''  ===
 +
Preparation of light meals and refreshments.  
 +
 
 +
=== Location and relationship  ===
 +
Drawing 21: Kitchenette
 +
 
 +
=== Activities  ===
 +
 
 +
* Storing lunch packs  
 +
* Preparing light meals  
 +
 
 +
* Making coffee/tea.  
 +
 
 +
=== Requirements  ===
 +
Work surface, storage space, cupboards  
 +
 
 +
Place for a fridge  
 +
 
 +
Position for food trolleys from catering service.  
 +
 
 +
=== Fixtures, fittings and equipment  ===
 +
 
 +
* Standing-height worktop  
 +
* Standing-height double-end, double-bowl wash-up sink on fixed legs  
 +
* Fridge  
 +
* Microwave oven  
 +
 
 +
* Toaster
 +
* Storage cupboards  
 +
* Hydroboil.  
 +
 
 +
== Staff Rest Room ==
 +
 
 +
=== Function  ===
 +
 
 +
* Space for staff to take tea and lunch breaks  
 +
* The space could also be used for staff meetings and training  
 +
* A minimum area of 15² is required, allowing 1.5m² per person. Size is dependent on the number of staff using the facility and the usage of the facility  
 +
* In district and regional hospitals, the staff room may also be used as a training area.  
 +
 
 +
=== Location and relationship  ===
 +
Drawing 22: Staff rest room
 +
 
 +
=== Activities  ===
 +
Eating  
 +
 
 +
Relaxing  
 +
 
 +
Informal meetings.  
 +
 
 +
=== '''Requirements'''  ===
 +
Area for relaxing.  
 +
 
 +
=== Fixtures, fittings and equipment  ===
 +
 
 +
* Desk/sitting-height worktop  
 +
* Pinning board  
 +
 
 +
* Whiteboard with marker tray  
 +
* Chairs and tables  
 +
* Water cooler  
 +
* Hot-water boiler  
 +
* Comfortable chairs  
 +
 
 +
* Tables  
 +
* Clinical hand-wash basin, complete with liquid-soap dispenser and paper-towel dispenser.  
 +
 
 +
== Female change rooms ==
 +
 
 +
=== '''Description and function'''  ===
 +
Female toilets and change area.  
 +
 
 +
=== Location and relationship  ===
 +
Outside the core activity area of the CSSD  
 +
 
 +
Drawing 23: Female change room
 +
 
 +
=== Activities  ===
 +
Shower  
 +
 
 +
Grooming  
 +
 
 +
Hand wash • Use of WC or urinal.  
 +
 
 +
=== Requirements  ===
 +
 
 +
* Secure storage of personal property is essential  
 +
 
 +
* Staff to provide their own padlocks.  
 +
 
 +
=== Fixtures, fittings and equipment  ===
 +
 
 +
* Clothes lockers with bench  
 +
* Sanitary o Shower  
 +
 
 +
* WC  
 +
 
 +
* Hand-wash basins  
 +
 
 +
* Hand-towel dispensers  
 +
* Soap dispenser  
 +
* Mirrors  
 +
* Toilet-roll holders.  
 +
 
 +
== Male change rooms ==
 +
 
 +
=== '''Function'''  ===
 +
Male toilet and change area.  
 +
 
 +
=== Location and relationship  ===
 +
Outside the core activity area of the CSSD  
 +
 
 +
Close to departmental entrance.  
 +
 
 +
Drawing 24: Male change room
 +
 
 +
=== Activities  ===
 +
 
 +
* Shower  
 +
* Grooming  
 +
* Hand wash  
 +
 
 +
* Use of WC or urinal.  
  
4.2. Location and relationship  
+
=== Requirements  ===
  
 +
* Secure storage of personal property is essential  
 +
* Staff to provide their own padlocks.  
  
 +
=== '''Fixtures, fittings and equipment'''  ===
  
 +
* Clothes lockers with bench  
 +
* Sanitary o Shower o Urinals  
  
 +
* WC  
 +
* Hand-wash basins  
  
 +
* Shoe racks  
  
 +
* Hand-towel dispensers  
 +
* Soap dispenser  
 +
* Mirrors  
 +
* Toilet-roll holders  
 +
* Laundry bag holders.  
  
 +
== Steriliser plant room ==
  
 +
=== '''Function'''  ===
 +
Service area of the sterilisers.  
  
 +
=== Location and relationship  ===
 +
Drawing 25: Steriliser plant room
  
 +
=== Activities  ===
  
 +
* Maintenance and repair of autoclaves by trained technical staff  
 +
* Sampling facilities for steam and water quality  
 +
* Limited access to trained skilled maintenance personnel only.  
  
 +
=== Requirements  ===
  
 +
* Technical personnel need to access the steriliser controls through the PPE room  
 +
* Waterproof, hardwearing floor, with a gradient in the direction of a floor drain  
 +
* Clearances as per specifications as steriliser manufacturers • Adequate space for maintenance and periodic testing is essential.    
 +
 +
Access to the maintenance area of the autoclaves must not interfere with the CSSD activities. For singledoor autoclaves, there must be no connecting door between the maintenance area and the sterilised supply store. The maintenance area in particular should be well ventilated by natural means assisted by mechanical extraction if necessary. Note that this only achievable with single door autoclaves. Where double door autoclaves are used care must be taken to identify an access point from within the unit, which causes least disruption.  
 +
 +
=== '''Fixtures, fittings and equipment'''  ===
 +
As per manufacturer’s specifications.  
 +
 +
=== Services  ===
 +
As per manufacturer’s specifications.
  
 +
= Building and Services =
  
  

Revision as of 11:03, 12 October 2020

Contents

General Planning Considerations

Sterilisation department in a hospital

The sterilisation department in a hospital is known by many acronyms, e.g.:

CSD Central Sterilisation Department

CPD Central Processing Area

SSD Sterile Service Department

TSSD Theatre Sterile Service Department

TSSU Theatre Sterile Service Unit

CSSD Central Sterile Service Department (the most widely used term in the South African context)

Location and functional relationship

Functional relationships to other departments

See Figure 1. The CSSD should be centrally located with ready access to all related service areas, such as the ICU, in-patient units and emergency unit. The department should also have direct access, either horizontally or vertically, to the operating theatres.

Deliveries and transportation routes

Trolleys are used as mode of transport for both receivables and deliveries. In order to cater for the high volume of trolleys to and from the CSSD receiving and dispatch areas, the entry/exit points should ideally be separated to create a uni-directional traffic flow and also to avoid cross-contamination through the division of the clean and dirty material.

Access for plant and equipment maintenance

Plant and equipment in service areas would need access from outside the CSSD, in order not to compromise the desired level of cleanliness in the unit. In some situations direct access between the plant area and the steriliser is required in order to allow access for maintenance staff to the equipment controls in the CSSD area side.

Figure 1: Departmental relationships (IUSS:GNS Adult Inpatient Services)

Primary function of a CSSD

The primary function of a CSSD is to provide an efficient, economic, continuous and quality supply of sterilised items, when needed, to all patient-care service points in the hospital, and to receive returned contaminated items for cleaning. This process is generally referred to as the “decontamination life cycle” (see Figure 2).

Figure 2: Decontamination life cycle

Activities in a CSSD can functionally be sorted under the following primary zones:

  • Dirty Decontamination Zone
  • Clean IAP (Inspection and Packing Zone)
  • Sterile Clean Zone

In addition to the above primary zones, supporting activities are accommodated in the CSSD.

Support zone

In order to identify the functional relationship between the various spaces, the convention is used throughout this guide to indicate the respective zones in the following colours:

In order to create a work space for maintaining a clean environment suitable for handling sterile articles, access to the red, blue and green zones is restricted and subjected to “red-line” principle.

In addition to the above, the red area (decontamination zone) is divided with a hard barrier from the IAP area, in order to prevent contaminated particles from freely entering the relatively cleaner IAP area. This barrier could be a solid brick wall, or glass wall.

Activities comprising the decontamination cycle should allow a progressive work-flow pattern that commences with a “dirty” entry and receiving area, proceeds to a cleaning, decontamination and drying area, into a sorting and packing area, through to sterilisation and cooling area, to finish with sterile storage, distribution and exit areas.

Figure 3: Work flow through the primary zones

Activities in a CSSD

The main activities of the “decontamination life cycle” taking place in a CSSD can be listed as follows:

  • receiving of soiled (and contaminated) returns
  • cleaning of trolleys
  • sorting returned trays
  • sorting, disassembling, cleaning and drying of all returned medical devices
  • checking functionality and cleanliness of cleaned medical devices
  • assembling, packing and wrapping of trays
  • sterilisation
  • cooling of sterile packs
  • storage of sterilised items
  • dispatching of orders
  • quality control
  • maintenance
  • record keeping
  • receiving new supplies.

These activities can be classified under the following functional areas:

Decontamination

Decontamination involves the use of automated and manual cleaning to remove harmful blood-borne pathogens on the surfaces of equipment and instruments. Soiled items for re-use (medical devices, textiles and equipment) are received in the sterilising department after use in the various clinical departments. These could be operating theatres, emergency department and various wards. Medical devices, equipment and other contaminated articles will be sorted, disassembled, pre-rinsed and cleaned in the decontamination/dirty area. Used linen is put into linen bags and sent to the laundry. Waste items are sorted into suitable containers, according to policy, for appropriate disposal methods.

If items are heavily soiled a manual washing procedure will precede the automated cleaning process by washer-disinfectors. For manual cleaning, a double- (two-) sink arrangement is optimal, one for cleaning and one for rinsing. Automated washers or washer-disinfectors can be provided as single or double-door designs (the latter to allow for physical separation of the dirty and clean areas of the decontamination area).

Photograph 1: Manual cleaning

Photograph 2: Automated cleaning

Inspection

Decontaminated medical devices and equipment are visually inspected for functionality, damage and cleanliness according to required standards, the manufacturer’s instructions and written protocols.

Photograph 3:

Packing

Decontaminated instruments, equipment and other articles are sorted, assembled, counted and packed prior to sterilizing.

Photograph 4:

Sterilisation

Sterilisation is a defined process used to render a surface or product free from viable organisms, including bacterial spores. Depending on the product this procedure could vary from steam sterilisation, dry heat sterilisation, to low temperature sterilising processes.

Photograph 5:

Storage

Sterile items are stored in a clean controlled environment to prevent re-contamination before use.

Photograph 6:

Figure 4: The decontamination life cycle at a glance

Functional Requirements

Activity zones in a typical CSSD

Figure 5: Dispatch points in the decontamination cycle

Figure 5 above is a variation of the generic ‘decontamination life cycle’, indicating the various dispatch points in the cycle.

Based on this principle, the activity spaces in a CSSD could be organised as per figure 6

Figure 6: Configuration of activity spaces

Decontamination zone

  • Receiving and sorting
  • Waste disposal 
  • Cleaner/sluice
  • Trolley wash 
  • Manual cleaning 
  • Automated cleaning 
  • Raw materials and chemicals storage
  • PPE area (gowning).

Figure 7: Areas related to the decontamination zone

Inspection and packing zone (IAP Zone)

  • Inspection and packing (IAP)
  • Sterile pack
  • Textile folding
  • Raw materials storage
  • PPE area (gowning).

Figure 8: Areas related to the inspection and packing zone

Sterile zone

  • Sterilisation
  • Cooling 
  • Sterile pack storage
  • Dispatch.

Figure 9: Areas related to the clean zone

Support zone

  • Office
  • Staff rest room
  • Kitchenette
  • Female change room
  • Male change room
  • Manager’s office
  • Steriliser plant room.

Figure 10: Areas related to the support zone

Functional relationship between activity spaces

Figure 11: Functional relationship between activity spaces

Workflow

Design solutions should follow work-flow principles, separating dirty and clean areas. The workspaces in the decontamination and clean areas should be designed as open-plan work areas subdivided by benches and/or equipment into functional work areas. These work areas should be arranged to allow for a progressive work flow that commences with a ‘dirty’ entry and receiving area, proceeding to a cleaning, decontamination and drying area, into a sorting and packing area, through to a sterilisation- and cooling area, with sterile storage, distribution and exit areas completing the process. 

It is critical to the functional efficiency and safety of the CSSD that these spaces are sequentially linked for one-way flow-through of instrumentation. The separation between the dirty area, where soiled goods are collected, and the clean area where washed and disinfected instruments are inspected, sorted and packed, is realised by a high throughput pass-through washer disinfector barrier.

Treated instruments are unloaded and managed directly in the clean packing area by different staff.

Figure 12: Work flow through the zones

Material flow

Figure 13: Material flow through the zones

Personnel flow

Figure 14: Personnel flow through the zones

Air flow

Figure 15: Air flow through the zones

General design considerations

Design for infection control

The design of a CSSD plays an essential role in addressing infection control issues to minimise the risk of infection transmission. 

Planning and design features to support infection control should include the following:

  • Restricted/controlled access
  • Unidirectional work flow, progressing from dirty to clean to sterile areas
  • Controlled air flow with positive air pressure from clean to dirty areas
  • Containment of steam and moisture, preventing potential contamination of stored sterile articles.
  • Building and layout details that would facilitate easy cleaning
  • Selection of suitable building materials and finishes
  • Selection of fixtures, fittings and equipment with suitable detail, materials and finishes for easy cleaning, and prevention of build-up of harmful organisms
  • Adequate facilities for cleaning and waste management
  • Access to the area should be limited and controlled. This should prevent any unauthorised person from entering the area without permission
  • Staff/visitors should have access to hand-washing facilities, separate from those used for cleaning devices, before entering or leaving the areas.
  • The flow of both staff and equipment must allow no cross-over of soiled and clean materials
  • The operating procedure for infection control in a CSSD falls outside the scope of this guideline.

Design for Occupational, Health and Safety

Planning and design features to support occupational health and safety include the following:

  • Selection of floor finishes with a non-slip finish
  • Selection of fixtures, fittings and equipment with suitable detail, materials and finishes to prevent personal injury through accidents or misuse
  • Provision of suitable and adequate facilities to support and encourage a high level of personal hygiene, with special reference to hand hygiene
  • Provision of adequate dispensing points for the appropriate personal protection items (PPE) for the specific area to enable strict enforcement of PPE requirements in the protection of healthcare workers, especially as preventive measures against HIV aids
  • Top-loading, worktop equipment should be accessible to staff members of all heights
  • Ill-considered dimensions and layouts of fixtures and fittings could have a significant negative effect on occupational health and safety of staff.

As the requirements of the Occupational Health and Safety Act will apply, this section needs to be read in conjunction with the OHS-related guidelines.

Design for change and technology

Although it is difficult to predict future trends in CSSD technology, it is advisable to allow some flexibility and adaptability in space requirements, electrical consumption and layout, and also in air-handling capacity. Current trends that need to be considered are the following:

  • The increasing complexity of surgical procedures requires more intricate equipment and instruments that need specialised care and handling during the sterilisation procedure
  • Integrated computerised tracking facilities have become widely used and have become an essential tool in the validation of the sterilisation process
  • Changing staff-flow patterns due to changing work-flow patterns as a result of procedural and/or equipment innovations
  • Design towards sustainable architecture, i.e. water-saving equipment, and equipment with reduced toxic emissions. Constant improvements and innovations lead to products that run more economically and reach a higher level of environment compatibility 
  • The facility should be able to reasonably accommodate access and positioning of possible outsize equipment. Consideration for this possibility should be given from (and including) point of delivery to point of positioning
  • It is advisable to allow capacity for extra machinery in the event of increased production demand.

Ergonomic and user-comfort considerations

Sterile services departments should be designed to protect staff from avoidable risks of injury. Badly designed elements such as height, depth and design of workstations and counters, shelving and the layout have an impact on the occupational health and safety of staff. Workspaces should therefore be sufficiently flexible and adaptable to accommodate adequate working space for individual comfort, and to reduce any unnecessary physical stress or risk of injury to the body from any repetitive and/or periodic actions such as lifting, pulling, pushing, etc. 

Ergonomics considers the understanding of human-equipment interaction and design to minimise safety risks and achieve the optimum use of equipment. When particular high risks are identified, these should be minimised when designing the facility – while providing good lighting (preferably natural light), adequate ventilation, plenty of space, and comfortable humidity/temperature conditions. Workbenches and chairs must be height-adjustable, allowing staff to adopt the correct posture when sitting or standing. 

Enough space must be available to allow for organisation of the workspace. All materials, for example those in the packing area, should be located within easy reach of the workbench (packaging materials, indicators, etc.). A similar concept should apply to device-sorting or manual-cleaning areas. There should be adequate space to manoeuvre, queue, and unload trolleys or other means of transportation.  This will allow not only for good ergonomics but also for efficient work practices. 

The provision of a pleasant interior environment can contribute to staff morale. Temperature and humidity control (air-conditioning), in particular in areas where heat-associated equipment (such as steam sterilisers and thermal washer-disinfectors) is used, is preferred. Provision must be made for adequate heat extraction systems from heat generating equipment such as autoclaves and instrument washers. This should be done as close to the source as possible i.e. above autoclave doors and instrument washers. This heat source can be utilized to pre-heat water going to the boilers. Consideration should also be given to ensure there is adequate lighting (preferably natural) and noise control. 

For larger facilities, provision may need to be made for managers’ offices, general staff areas (for eating and drinking) and storage areas that are separated from the decontamination area. Good interior design also contributes to staff morale. The aim should therefore be to create an attractive and cheerful environment throughout the department.

Sound

Noise must be controlled

  • A threshold of 60dBA (decibel) must not be exceeded 
  • The walls and ceilings should be made of absorbent materials so that they do not reflect sound 
  • Insulation of sterilisers and washer-disinfectors in technical walls will reduce the noise level
  • Offices should allow confidential discussions to take place in privacy, away from noisy mechanical or high-volume human areas.

Natural light

Natural lighting is highly desirable, especially in the work areas, and should be used wherever possible, especially in areas such as the cleaning and packing areas. However, direct sunlight on work spaces should be avoided.

Natural ventilation

Natural ventilation through opening-section windows should be limited to offices and staff rooms. However, this is not recommended as it could promote contamination of the internal space by outside sources. Mechanical ventilation should be provided through the remainder of the CSSD, with good primary and secondary filters which must be monitored with differential manometers linked to an alarm system.

Communication

Provision must be made for communication systems to minimise the passage of staff to and from the clean zone. Glass partitions, communication panels, IT and video links for data transfer, intercom and telephones can serve as appropriate means of communication. 

Glass partitions should be used to permit observance of the activities within the clean zone (from the outside) without having to enter it. The glass panels must be of a non-opening design and must be waterproof and flush-mounted.

CSSD Area Determination

Determination of size and layout

The size of a CSSD in a hospital is unique to that hospital, as the size, layout and function of a CSSD are defined in the Operational Policy Statement that guides the operational management of the hospital. The operational policies specific to the CSSD precede sketch design stage. These policies are developed by the project team in consultation with health; service stakeholders, who should have the knowledge and experience to analyse the various processes in and related to the CSSD.

These operational policies define the “What, How, When, Where, Who and With What” of any activity and/or process and are major space determinants which could significantly affect the planning and design of the CSSD, as they can have an impact on the size, configuration and the nature of accommodation.  Operational policies will vary from unit to unit depending on a wide range of factors, both external and internal to the CSSD.  

Determining factors external to the CSSD

Examples of these space determinants could include the following:

  • number of theatres/case mix
  • surgical procedures
  • extent of storage in the theatres and wards
  • distribution system that will be used (vertical, horizontal, trolleys, lifts)
  • amount of space needed for waste management
  • processing needs for re-usable textiles (receiving, transporting, collecting, storing)
  • staff facilities to be shared with adjacent departments. See annexure A for a generic set of Standard Operating Policies (SOP) for a typical sterile service department.

Determining factors internal to the CSSD

Examples of these space determinants could include the following:

  • types of processing equipment to be used (washer, washer-disinfectors, single- or multi-chamber washers, ultrasonic cleaners, endoscope processors)
  • types of packaging to be used (disposable wraps and pouches, re-usable wraps, rigid containers
  • echnology to be used for sterilisation (high temperature or low temperature sterilisation, other chemical sterilants, steam)
  • anticipated inventory storage
  • anticipated volume of consumable supplies
  • type of documentation and record-keeping system to be used (manual vs computerised)
  • instrument inventory
  • equipment inventory
  • projected workload
  • staffing structure – number of offices
  • staffing policy - number of staff to be accommodated
  • types of cleaning equipment selected such as multi chamber or single chamber
  • number of sterilisers and whether front or double sided loading
  • emergency sterilisation requirements.

CSSD area determination

Hoët (1989 cited in AFS Working Group, 2008b, p.281) has estimated the following ratios as a broadbased calculation of CSSD space:

  • 0.7 m²/bed from 0 to 300 beds
  • 0.6 m²/bed from 300 to 600 beds
  • 0.5 m²/bed for more than 600 beds.

Based on these ratios, the following table can be compiled:

Table 2:mratio of hospital bed to CSSD area

BED SIZE   CALCULATION   SURFACE AREA  
200 BEDS   0.7 m² /bed   210 m²  
400 BEDS   0.6 m² /bed   240 m²  
600 BEDS   0.5 m² /bed   300 m²  
800 BEDS   0.5 m² /bed   400 m²  
1000 BEDS   0.5 m² /bed   500 m²  
1200 BEDS   0.5 m² /bed   600 m²  

AFS Working Group (2008b, p.291) states that the CSSD has few internal corridors, the commonly used net to department functional factor adopted is 1.30. The 1.30 factor anticipates that the internal circulation must be added to connect functional areas and individual rooms. This minimal surface area required can be estimated as being 200m² useful and 260m² net floor areas.  

Based on the above assumption, AFS Working Group (2008b, p.291) calculates the useful surface area using the MSO ratio based on the number of beds used for Medical – Surgery – Obstetrics (MSO), using the following calculation basis:  

Table 3: Ratio of MSO to CSSD area

MSO – NR OF BEDS   USEFUL SURFACE AREA/BED   USEFUL SURFACE AREA   NET SURFACE AREA  
< 200 BEDS   200   200 m²   260 m²  
200 – 300 BEDS   1,5 m² /bed   300 – 400 m²   400 - 520 m²  
300 – 400 BEDS   1,2 m² /bed   350 – 420 m²   450 – 550 m²  
450 + BEDS   1,0 m² /bed   450 m²   600 m²  

Studies done by Putsep and Cowan (1983, p.8) produced the following ratios depending on the ‘active’ nature of the bed.  

Table 4: Comparative recommendations for estimating the size of a CSSD (Putsep and Cowan,1983, p.8)

NR OF  

BEDS  

SCANDINAVIA   BELGIUM   NETHERLANDS   RSA1  
  m² PER BED  
200 BEDS   1,1 m² /bed   0,6 - 1 m² /bed   0,7 m² /bed   1,0 m² /bed23  
350 BEDS   1,1 m² /bed   0,6 - 1 m² /bed   0,6 m² /bed   1,0 m² /bed  
500 BEDS   1,1 m² /bed   0,6 - 1 m² /bed   0,5 m² /bed   1,0 m² /bed  
750 BEDS   1,1 m² /bed   0,6 - 1 m² /bed   0,4 m² /bed   1,0 m² /bed  

 

Based on the above data, the areas are as follows:  

NR OF  

BEDS  

SCANDINAVIA   BELGIUM   NETHERLANDS   RSA3  
  TOTAL AREA  
200 BEDS   220 m²   160 m²*4   140 m²   200 m²  
350 BEDS   385 m²   280 m² *   210 m²   350 m²  
500 BEDS   550 m²   400 m² *   250 m²   500 m²  
750 BEDS   825 m²   600 m² *   300 m²   750 m²  

As the schedules of accommodation on which the above analyses are based have not been included in the study, the equitability of the comparisons is in doubt.  

It is however; clear that the size of a CSSD cannot be generically determined on the basis of statistics or averages. Every CSSD has its own set of area determinants that need to be logically evaluated in order to arrive at an area that is the optimal combination of functionality and cost effectiveness.  

Proportional allocation of space in a CSSD facility

Table 5: Space allocation in a CSSD (Putsep and Cowan,1983, p.9)

AREA   NUFFIELD  

PROVINCIAL  

HOSPITALS TRUST  

(1963)  

ESTIMATED  

AVERAGE –  

SWEDISH  

PRACTICE  

NORWEGIAN  

RECOMMENDATIONS  

(1978)  

HOET  

(1981)  

RECEIVING  

WASHING  

DECONTAMINATION  

10   19   10   30  
CLEAN AREA   35   20   25   30  
STERILISATION AREA   5   8   5   25  
STERILE SUPPLY  
STORE DISPATCH   16   29   25  
BULK STORE   11   14   20   15  
STAFF AREA  

OFFICE  

HOUSEKEEPING  

23   10   15  

AFS Working Group (2008b, p.291) states that the areas within the CSSD can be sub-divided as follows:  

Receiving: 10% of the surface area  

Decontamination: 25% of the surface area  

DIRTY 35%


IAP  35% of the surface area

CLEAN   35%


Sterile Storage 20% of the surface area

STERILE   20%


Annexes: 10% of the surface area

SUPPORT 10%  

If the generic plan used as basis for this study (LAYOUT 2.1) is subjected to an area analysis, the following table can be compiled (TABLE 4.5) for an autonomous (support services not shared) CSSD of 600m². If staff facilities and corridors are shared with another department (e.g. theatre department), the CSSD’s size reduces to 450m² as per TABLE 4.6, illustrating the difficulty in achieving universally applicable areas, and the effect of hospital-specific policies.  

It is significant that the percentage of total areas of TABLE 4.6 compares favourably with the AFS Working Group’s recommendations.  

Table 6: Proportional space allocation - Generic layout (600M2 gross area)

DIRTYCLEANSTERILE SUPPORT
Area (m²) Area (m²) Area (m²) Area (m²)
WASTE DISPOSAL 12
SLUICE 12
RECEIVING & SORTING 25
TROLLEY WASH 5
TROLLEY HOLDING 5
STORE 12
PPE TO DECON AREA 8
DECONTAMINATION AREA 100
PPE TO IAP AREA 8
STORE 12
TEXTILE AREA 16
INSPECTION & PACKING 100
STERILIZATION 30
DISPATCH 15
STERILE STORE 40
COOLING 30
STERILIZER PLANT ROOM 18
OFFICE 12
KITCHENETTE 12
STAFF REST ROOM 35
FEMALE CHANGE 30
MALE CHANGE 15
CSSD CORRIDOR 48
TOTAL AREA (SQ M)     179 166 85 170
% OF TOTAL AREA     30% 28% 14% 28%

Table 7: Proportional space allocation - Generic layout without staff facilities (450M2 gross area)

DIRTY CLEAN STERILE SUPPORT
Area (m²) Area (m²) Area (m²) Area (m²)
WASTE DISPOSAL 12
SLUICE 12
RECEIVING & SORTING 25
TROLLEY WASH 5
TROLLEY HOLDING 5
STORE 12
PPE TO DECON AREA 8
DECONTAMINATION AREA 100
PPE TO IAP AREA 8
STORE 12
TEXTILE AREA 16
INSPECTION & PACKING 100
STERILIZATION 30
DISPATCH 15
STERILE STORE 40
COOLING 30
STERILIZER PLANT ROOM 18
OFFICE 12
TOTAL AREA (SQ M)     179 166 85 30
% OF TOTAL AREA     39% 36% 18% 7%

Typical Floor Layouts

The following generic plans are included to illustrate the combined effect of gross floor area allocation, proportional space allocation, and work-flow requirements.  

Drawing 1: Typical floor layout (Small - 250M² gross area) not to scale Proportional Net space allocation

DIRTY   37%  
CLEAN   36%  
STERILE   21%  
SUPPORT   6%  

Drawing 2: Typical floor layout (Medium - 400M² gross area) not to scale Proportional Net space allocation

DIRTY   38%  
CLEAN   33%  
STERILE   22%  
SUPPORT   7%  

Drawing 3: Typical floor layout (Large - 600M² gross area) not to scale Proportional Net space allocation

DIRTY   30%  
CLEAN   28%  
STERILE   14%  
SUPPORT   28%  

Individual Space Requirements

CSSD Layout Unpacked

Due to the uni-directional sequential nature of the work flow in the CSSD, activities are interrelated and inter-dependent. It is, therefore, critical to the functional efficiency and safety of the CSSD that those areas are sequentially linked for uni-directional flow-through of instrumentation, with no room for back tracking.  

The above work flow and interrelationship between the adjacent areas dictates the characteristics of each space. In order to discuss each area individually, it is necessary to have a base plan as a reference point. The typical floor layout based on a 600m2 unit will be used for this purpose.

Drawing 4: A generic layout to illustrate room layouts

Receiving and Sorting

Function  

This is the area where all soiled articles for reprocessing are received on trolleys from the main corridor from user departments throughout the hospital.  

Location and Relationship  

  • Close to main entry doors to the CSSD unit  
  • Visual access to main entry.  

Drawing 5: Receiving and sorting

Activities  

  • Access for deliveries of supplies, return of contaminated goods and the collection of waste and contaminated linen  
  • Contaminated articles are received at a counter with a trolley hatch, where the articles are logged, sorted and forwarded to the decontamination area  
  • Contaminated linen is put into linen bags and stored in the waste-disposal store for transport to the laundry  
  • Supplies are received in the supplies store where they are opened and packaging is discarded in the waste-disposal store  
  • Trolleys are sent to the trolley wash bay.  

Requirements  

  • Visual access to entrance doors  
  • All entrances should be secure and controlled by means of communication to prevent access by unauthorised people  
  • A glass partition with lockable sliding hatch between this area and the corridor • A lockable hatch for trolleys  
  • The red-line principle is applicable at the receiving area; only material and trolleys are to enter the CSSD via this entrance • Worktop for unpacking and sorting  
  • Hand-washing facilities.  

Fixtures, fittings and equipment  

  • Receiving counter with pass-through hatch and trolley hatch, acting as red line  
  • Sorting work tables – standing height  
  • Clinical hand-wash basin, complete with liquid soap dispenser and paper-towel dispenser • Space should be allowed for record-keeping and record-keeping supplies.  

Photograph 7: Trolley pass-through hatch (Tygerberg hospital)

Services  

  • 2 x telephones  
  • 2 x data points  
  • CSSD technician call system  
  • Power outlets for computer points, computer, fax and printer  
  • Access control to outside door.

Waste Disposal

Function  

Contaminated waste articles are stored for collection and transport to the respective disposal areas.  

Location and relationship

Attached to the receiving area.  

Drawing 6: Waste disposal

Activities  

  • The sluice area and waste-disposal area could be combined in smaller units  
  • Contaminated waste articles are temporarily stored for collection and transport to the respective disposal areas  
  • Contaminated linen is temporarily stored in canvas bags for collection and transport to the laundry  
  • Third-party collection area (depot).  

Categories of waste stored in the waste-disposal area could include:  

  • Health-care waste, infectious waste, sharps  
  • General office waste  
  • Packaging and cartons from bulk supplies stored in the unit • Linen bags used to collect reusable items  
  • Sharps from theatres.  

Requirements  

  • An independent secure area for temporary storage of clinical waste awaiting collection in accordance with local waste management policy  
  • The door to the receiving/sorting area side should be lockable from the CSSD side to prevent unauthorised entry  
  • Room layout should allow for easy recycling/re-use/disposal policy  
  • Space for linen bags and waste containers  
  • An impermeable, hard-wearing floor with good drainage; it should be easy to clean and to disinfect, with an accessible water supply for cleaning purposes  
  • The area should be protected from outside elements, inaccessible to animals, insects or birds and not situated in close proximity to fresh food stores, food preparation areas or patient waiting areas  
  • It should be sized according to the volume of waste generated by the facility as well as the frequency of collection.  
  • A bumper rail to protect the wall behind the trolleys • Containers according to waste policy.

Photograph 8: Soiled-Linen trolleys

Photograph 9: Infectious-waste and sharps-disposal containers

Fixtures, fittings and equipment  

• Clinical hand-wash basin, complete with liquid-soap dispenser and paper-towel dispenser.  

Sluice

Function  

Heavily soiled items are rinsed and waste items are discarded in suitable containers.  

Location and relationship  

Drawing 7: Sluice area

Activities  

  • Cleaning of heavily soiled items  
  • Storing and cleaning of domestic cleaning equipment and holders (buckets, etc.).  

Requirements  

  • Some lumens may require irrigating with a high pressure water-jet spray gun  
  • Heavily soiled instruments should be pre-rinsed using a submerged high-pressure water gun in a sluice area.  

Fixtures, fittings and equipment  

  • Above-sink storage facilities for cleaning material and equipment  
  • Sluice unit  
  • Bucket sink  
  • Mop/broom rail.  

Photograph 10: High-pressure water gun

Photograph 11: Drip sink with hinged bucket gridPhotograph 12: Double-bowl sink unit

Trolley wash and storage

Function  

Area for washing, disinfecting and storing of trolleys.  

Location and relationship  

Drawing 8: Trolley wash and storage

Activities  

  • This area receives returned contaminated trolleys from the decontamination area  
  • Trolleys are washed and cleaned before being moved through a trolley hatch to the holding bay  
  • Washed trolleys are temporarily stored in the holding bay until required.  

Requirements  

  • Trolleys must be transferred via a trolley hatch to prevent entry  
  • The floor in the washing bay needs to have a gradient and floor drain, as well as hosing facilities  
  • Trolley-washing facilities with adequate drainage.  

Fixtures, fittings and equipment  

  • Trolley pass-through hatch  
  • Stainless steel sink • Water hose with hand-spray.  

Photograph 13: Trolley pass-through hatch (Tygerberg hospital)Photograph 14: Trolley cleaning (Tygerberg hospital)

Services  

  • Cold water for water hose  
  • Floor drain in vicinity of wash stations and equipment loading/unloading areas.  

Decontamination Area

Function  

This area is used to sort instruments followed by manual or automated cleaning.  

Soiled instruments are placed in a pass through washer disinfector that will deliver clean instrumentation to the IAP Area. Selected items may be manually cleaned, because they are either too delicate or will not fit into the washer disinfector, then forwarded to the clean area via a pass-through hatch.  

Drawing 9: Automated cleaning area

Activities  

  • Selective manual cleaning of instruments and equipment not suitable for automated cleaning.  
  • Disassembly and inspecting of contaminated returns  
  • Rinsing of instruments and equipment  
  • Sorting and loading of medical instruments and equipment into trays/washer-disinfectors and other automated cleaning equipment.  

Requirements  

  • Sufficient wall-mounted brackets for cleaning chemicals and brushes  
  • Sealed closed windows to the outside would be desirable  
  • Space to park trolleys is essential  
  • Automated double-sided washer-disinfectors and ultrasonic cleaners are required for cleaning and drying of all suitable instruments and equipment. A minimum of two washing units should be provided to allow for maintenance and down-time  
  • Transfer hatch with sliding opening section (upwards or sideways) for the transfer of handwashed items and return of emptied disinfector trays  
  • The decontamination area has to be divided with a hard barrier from the IAP area, in order to prevent contaminated particles from freely entering the relatively cleaner IAP area. This barrier could be a solid brick wall or washer-disinfectors with panelling. A glass partitioning will contribute to an open-plan environment  
  • Adequate space should be allowed for trolleys to be manoeuvred without interfering with the work stations  
  • The distance between tables should be about 1.5m and between a table and the wall not less than 1,2m.  

Fixtures, fittings and equipment  

  • Stainless steel standing-height sorting tables with high-level shelves  
  • Ultrasonic cleaner, according to service requirements  
  • Washer-disinfectors with a drying cycle for instruments and tubing, according to service requirements  
  • De-ionised, distilled, or reverse osmosis (RO) water for final rinsing is preferable  
  • Drying rack - work space must be available for drying manually cleaned instruments  
  • Double-bowl stainless steel pot-wash type sink with draining boards on both sides  
  • Tubing manifolds (air and water) and additional water outlets for water pistols  
  • A 1000mm-long flexible hose with a tapered-nozzle water pistol for cleaning narrow-bore tubes should be fitted over the space between the bowls  
  • All taps to sinks should have threaded nozzles to allow for the fitting of a variety of cleaning gadgets  
  • Compressed-air outlets and pressure guns are required at all cleaning sinks  
  • Clinical hand-wash basin, complete with liquid-soap dispenser and paper-towel dispenser  
  • Wall-mounted cartridge soap dispenser  
  • Eye wash and first aid area  
  • Automated washer disinfectors with a choice of racks for respiratory equipment washer, bowls, basins, containers, etc.  
  • Transfer trolleys  
  • Waste container for non-regulated waste and sharps  
  • One height-adjustable chair per table  
  • A silent clock • Storage shelving.  

Photograph 15: Washer/disinfectors (Tygerberg hospital)Photograph 16: Washer/disinfectors trays returned to the decontamination area via pass-through hatch(Tygerberg hospital)

Photograph 17: Pass-through between decontamination and IAP areas (Tygerberg hospital)

Services  

  • Services to automated disinfectors as per manufacturers’ specifications  
  • Floor drains  
  • Trap for equipment drainage.  

Raw materials and chemicals store

Function  

Storage of consumables, raw goods and materials, and chemicals used in the decontaminated area.  

Location and relationship  

Drawing 10: Raw materials and chemicals store

Activities  

  • Receiving and storing of raw materials and consumables  
  • Distribution of goods to process areas  
  • Facilitating the disposal of transport packaging  
  • Storage of consumables, raw goods and materials, and chemicals used in the decontaminated area.  

Requirements  

  • Lockable transfer hatch on top of a worktop between this area and the department corridor  
  • Suitable slatted shelving for the range of consumables and chemicals that are stored in this room • Space for receipt, quarantine, inspection and acceptance of materials  
  • The store should be lockable.  

Fixtures, fittings and equipment  

  • Slatted shelving  
  • Transfer hatch.  

 PPE Area - Gowning (to contaminated area)

Function  

The PPE (personal protective equipment - gowning) room provides the only access to and from the decontamination area for staff, after putting on the appropriate PPE over garments and footwear.  

Location and relationship  

The PPE room is the only human entry/exit point between the decontamination area and the CSSD departmental corridor.  

Drawing 11: PPE Gowning area

Activities  

  • The PPE gowning room provides the only access to and from the decontamination area for staff.  
  • Facilities are provided for the storage and dispensing of personal protective equipment (PPE) over garments and footwear suitable for the decontamination-room activities  
  • It provides facilities for hand-washing before/after activities in the decontamination area  
  • The PPE area serves as transfer point into/out of the red-line area.  

Requirements  

  • PPE dispensers.  
  • Red-line demarcation barrier, with step-over wall  
  • There should be vision panels in doors and walls.  

Fixtures, fittings and equipment  

  • Shelving for PPE dispensers  
  • Footwear and over-garment storage  
  • Waste containers – either foot-operated or wall-mounted  
  • Clinical hand-wash basin complete with liquid-soap dispenser, paper \-towel dispenser, and mirror.  

Inspection and packing area (IAP Area)

Function  

Decontaminated instruments, equipment and other articles are inspected and packed here.  

Location and relationship  

The IAP area must be divided by a hard barrier from the decontamination area, in order to prevent crosscontamination. This barrier could be a solid brick wall or built in washer-disinfector with panelling, but a glass wall will contribute to an open-plan environment.

Drawing 12: Inspection and packing area

Activities  

  • Inspecting, functionality testing, assembling and packing cleaned and disinfected medical devices and accessories, according to predetermined required standards, in preparation for sterilisation  
  • Packs are checked, reassembled, double-wrapped, labelled, dated, and signed on the checklist by the packer  
  • Delivering items to the steriliser loading area • Returning racks to the decontamination area.  

Requirements  

  • Sufficient wall-mounted brackets for equipment  
  • Sealed closed windows to the outside would be desirable  
  • Space to park trolleys is essential  
  • Automated double-sided washer-disinfectors and ultrasonic cleaners are required  
  • Transfer hatch with sliding opening section (upwards or sideways) for the transfer of manually cleaned items, and return of empty washer racks  
  • The IAP area must be divided by a hard barrier from the decontamination area, in order to prevent cross-contamination  
  • Adequate space should be allowed for trolleys to manoeuvre without interfering with the work stations  
  • The distance between tables should be about 1.5m, and that between a table and the wall not less than 1.2m  
  • Packing tables require power and ICT connections for use with computers and instrument scanners  
  • Space for mobile shelving units containing the items awaiting packaging.  
  • Sterilisation wrap storage space/rack  
  • Hand rub station  
  • Clean environment with good lighting for inspections • There should be vision panels in doors and walls.  

Photograph 18: Visual-inspection of a device set following a cleaning process

Fixtures, fittings and equipment  

  • Packing table(s) 2000mm x 700mm, by 800mm high, with a shelf below its surface and a basket rack above it  
  • Stainless-steel worktop space for a variety of activities  
  • Stainless-steel storage for raw materials  
  • High level storage for tray checklists  
  • Mobile, height-adjustable chairs/stools • Table mounted lighted magnifiers • Hand rub station.  

Photograph 19: Textile folding tables (Tygerberg hospital)Photograph 20: Stainless steel worktop (Tygerberg hospital)

Services  

  • Sufficient plug points for power to equipment on the packing tables should be ceiling-suspended  
  • Medical-grade compressed air.  

Raw materials store for IAP Area

Function  

Storing of materials used for processing in the clean side of the CSSD.  

Location and relationship  

Drawing 13: Raw materials store for IAP area

Activities  

Storing of materials used for processing in the clean side of the CSSD.  

Requirements  

Lockable transfer hatch on top of a worktop between this area and the department corridor.  

Suitable slatted shelving for the range of consumables and chemicals that are stored in this room.  

Fixtures, fittings and equipment  

  • Slatted shelving  
  • Transfer hatch.  

Textile room

Function  

Receiving, folding, packing, and storing of textile materials.  

Location and relationship  

The textile room should be in close proximity to the IAP area, but also have a hatch to the CSSD departmental corridor to receive deliveries from the laundry.

Drawing 14: Textile room

Activities  

  • Due to linting, linen MUST be folded in a separate room with its own air-conditioning.  
  • Once laundered, ironed, checked and folded, clean unwrapped textiles should be handled as little as possible and be placed in a positive-pressure, temperature-controlled, and properly ventilated area with limited access in order to prevent accumulation of dust and lint.  

Requirements  

  • Receiving hatch to departmental corridor side  
  • The area used for the textile preparation should be physically separated from all other areas  
  • The ventilation system should be designed so that air flows into the textile preparation area (via negative pressure)  
  • The air flow should be of a down-draft type, and the number of air exchanges per hour should be sufficient to minimise lint particles in the air  
  • Vision panels in doors and walls.  

Fixtures, fittings and equipment  

  • Clinical hand-wash basin, complete with liquid-soap dispenser and paper-towel dispenser  
  • An illuminated linen inspection and folding table, 1800mm x 1250mm by 800mm high, with a foot switch to operate the light only during inspection. An acid-etched glass with the etched surface facing inwards would reduce the glare  
  • Shelving  
  • Stainless steel standing-height processing tables • Pass-through window.  

 Photograph 21: Textile folding table

Building services  

Extraction with lint filter.  

PPE Gowning area (to clean area)

Function  

The PPE (gowning) room provides the only access to and from the decontamination area for staff, after putting on the appropriate PPE (personal protective equipment - over garments and footwear).

Location and relationship  

The PPE room is the only human entry/exit point between the clean/IAP/steriliser/sterile storage area and the CSSD departmental corridor.  

Drawing 15: PPE Gowning area (IAP area)

Activities  

  • The PPE (gowning) room provides the only access to and from the clean/IAP/steriliser/sterile storage area for staff  
  • Facilities are provided for the storage and dispensing of PPE (personal protective equipment - over garments and footwear) suitable for the decontamination room activities  
  • The room provides facilities for hand decontamination before/after activities in the clean (IAP) area  
  • It serves as transfer point into/out of the red-line area.  

Requirements  

  • PPE dispensers.  
  • Red-line demarcation barrier, with step-over wall  
  • There should be vision panels in doors and walls.  

Fixtures, fittings and equipment  

  • Shelving for PPE dispensers  
  • Footwear and over-garment storage  
  • Waste containers – either foot operated, or wall-mounted  
  • Clinical hand-wash basin, complete with liquid-soap dispenser, paper-towel dispenser and mirror.  

Function  

Area where loading trolleys are parked, sterilisers are loaded, sterilisation cycles are run, sterilisers are unloaded, sterilised packs are cooled, following completion of the sterilisation cycle. The size of the area will be dependent on the number and type of sterilisers installed and whether single- or double-door.

Location and relationship  

  • This area is the transition from clean to sterile area  
  • The sterilisation area should be adjacent to the preparation and packaging area.  

Drawing 16: Sterilisation area

Activities  

  • Receiving packaged products from IAP  
  • A holding area for loaded and empty sterilisation trolleys  
  • Loading sterilisers  
  • Unloading single-door sterilisers  
  • Facilitating validation and routine testing of sterilisers  
  • Cooling of sterilised goods  
  • Where single-door autoclaves are installed, the autoclaves will be loaded and unloaded in the same area  
  • Where double-door autoclaves are installed, the unloading area is separate from the loading area  
  • In both cases, a separate cooling area from the loading area is required.  

Requirements  

  • Sufficient sterilisers to meet hospital needs  
  • Preferably sterilisers should be located in a restricted access area  
  • Autoclaves should not be located in high-traffic areas or near any potential sources of contamination, wash sinks, or containers for the disposal of linen and trash  
  • Material should flow from the preparation and packaging area to the sterilisation area and then on to sterile storage or distribution  
  • The ventilation system should be designed so that air flows out of the sterilisation area (via positive pressure)  
  • Circulation space for the free and unhindered manoeuvring, loading and unloading of steriliser trolleys  
  • Exhaust over the front of the steriliser doors to extract heat and steam, in order not to compromise the HVAC air flow and temperature. An extraction system which is activated by the autoclave door opening rather than a constant extraction system should be considered  
  • It is generally advisable to install two smaller autoclaves rather than one large one  
  • An extra autoclave should be provided to cater for exceptional demand, maintenance and breakdown  
  • A clear space of 2m in front of the autoclave is needed to facilitate the handling of loading trolleys  
  • No partition wall should be closer than 750mm to any autoclave  
  • The autoclaves must be well insulated. The emission of heat to the environment must be minimal, and adequate extraction facilities should be provided to remove hot air and steam from the autoclave at a rate equivalent to 15 air changes per hour  
  • Require separate installation and accommodation according to manufacturer's recommendations  
  • The size of the area will be dependent on the number and type of sterilisers installed and, importantly, whether the sterilisers are single- or double-sided  
  • A duct enclosure can also minimise heat build-up within the workroom. An exhaust over the front of the steriliser(s) should be considered, to extract both heat (cabinet) and steam (opening door).  

Fixtures, Fittings and Equipment  

• Adequate space should be allowed for sterilisers and aerators; loading, cooling of autoclave racks, storage of long, heat-resistant gloves • Autoclave cleaning supplies.  

Photograph 22: Autoclave trolley ready for loading (Tygerberg hospital)

Cooling Area

Description and function  

This area is used for the cooling of sterilised items on trolleys after being removed from the sterilisers.  

The size of the area will be dependent on the number and type of sterilisers installed.  

Location and relationship  

This area is directly adjacent to the sterilisation area. Sterile items are temporarily stored here until cooled.

Drawing 17: Cooling Area

Activities  

  • Cooling of sterilised items  
  • Transferring cooled items to storage.  

Requirements  

  • Sufficient space for trolleys to stand and manoeuvre until they have been cooled and inspected • This should be a clear open space with sufficient room to manoeuvre sterilising trolleys  
  • Demarcated bay – floor marking.  

Sterile Stores

Description and function  

A dedicated sterile storage and dispatch area.  

Location and relationship  

The sterile storage area should be located adjacent to the sterilisation area preferably in a separate, controlled, enclosed, limited-access area, the only function of which is to store sterile supplies.  

Drawing 18: Sterile pack store

Activities  

Storing of sterile packs.  

Requirements  

  • Supply air pressure should be positive with respect to surrounding areas and the level of filtration should be equal to that in an operating theatre  
  • There should be vision panels in doors and walls  
  • Area to be protected from direct sunlight  
  • Adequate and appropriate stainless steel slatted shelving in a clean environment  
  • Adequate and appropriate mobile storage systems and trolleys.  

Fixtures, fittings and equipment  

  • Closed or covered mobile storage systems are preferable for high-traffic areas  
  • Open or wire shelving is suitable for confined storage areas, provided that proper attention is given to traffic control, area ventilation, and housekeeping  
  • Hand rub station.  

Dispatch Desk

Function  

Distribution of sterile items to the various user departments.  

Drawing 19: Dispatch desk

Activities  

  • Dispatch of sterile items to the theatres and wards • Loading of sterile articles on trolleys  
  • Logging of dispatched deliveries.  

Requirements  

  • Counter with service hatch and trolley pass-through hatch  
  • Red-line principle is applicable  
  • No general access is allowed into the sterile storage and dispatch area.  

Fixtures, fittings and equipment  

  • Trolley pass-through hatch and counter hatch  
  • Clinical hand-wash basin, complete with liquid-soap dispenser and paper-towel dispenser  
  • Stainless steel shelving  
  • Filing cabinet  
  • Desk  
  • Chair  
  • Telephone  
  • Work surface  
  • Hand rub station.  

Office

Function  

A space for administration/management.  

Location and relationship  

Drawing 20: Office

Activities  

  • Making and receiving phone calls  
  • Writing reports  
  • Access and printing data from computer  
  • Unit management  
  • Shift handover meetings  
  • Staff management  
  • Record keeping and storage.  

Requirements  

  • The office should be lockable  
  • No direct access from this area to the work areas is allowed. This area can also have a hatch link to the main hospital passage so that suppliers can interact with the unit manager without coming into the unit. This would be an infection risk.  

Fixtures, fittings and equipment  

  • Desk/sitting-height worktop  
  • Pinning board  
  • Whiteboard with marker tray  
  • Blinds for privacy  
  • Chairs  
  • Filing cabinet
  • Shelving  
  • Filing cabinet
  • Stationery cupboard.  

Services  

  • IT and data connections  
  • Electrical points • Telephone point.  

Kitchenette

Function  

Preparation of light meals and refreshments.  

Location and relationship  

Drawing 21: Kitchenette

Activities  

  • Storing lunch packs  
  • Preparing light meals  
  • Making coffee/tea.  

Requirements  

Work surface, storage space, cupboards  

Place for a fridge  

Position for food trolleys from catering service.  

Fixtures, fittings and equipment  

  • Standing-height worktop  
  • Standing-height double-end, double-bowl wash-up sink on fixed legs  
  • Fridge  
  • Microwave oven  
  • Toaster
  • Storage cupboards  
  • Hydroboil.  

Staff Rest Room

Function  

  • Space for staff to take tea and lunch breaks  
  • The space could also be used for staff meetings and training  
  • A minimum area of 15² is required, allowing 1.5m² per person. Size is dependent on the number of staff using the facility and the usage of the facility  
  • In district and regional hospitals, the staff room may also be used as a training area.  

Location and relationship  

Drawing 22: Staff rest room

Activities  

Eating  

Relaxing  

Informal meetings.  

Requirements  

Area for relaxing.  

Fixtures, fittings and equipment  

  • Desk/sitting-height worktop  
  • Pinning board  
  • Whiteboard with marker tray  
  • Chairs and tables  
  • Water cooler  
  • Hot-water boiler  
  • Comfortable chairs  
  • Tables  
  • Clinical hand-wash basin, complete with liquid-soap dispenser and paper-towel dispenser.  

Female change rooms

Description and function  

Female toilets and change area.  

Location and relationship  

Outside the core activity area of the CSSD  

Drawing 23: Female change room

Activities  

Shower  

Grooming  

Hand wash • Use of WC or urinal.  

Requirements  

  • Secure storage of personal property is essential  
  • Staff to provide their own padlocks.  

Fixtures, fittings and equipment  

  • Clothes lockers with bench  
  • Sanitary o Shower  
  • WC  
  • Hand-wash basins  
  • Hand-towel dispensers  
  • Soap dispenser  
  • Mirrors  
  • Toilet-roll holders.  

Male change rooms

Function  

Male toilet and change area.  

Location and relationship  

Outside the core activity area of the CSSD  

Close to departmental entrance.  

Drawing 24: Male change room

Activities  

  • Shower  
  • Grooming  
  • Hand wash  
  • Use of WC or urinal.  

Requirements  

  • Secure storage of personal property is essential  
  • Staff to provide their own padlocks.  

Fixtures, fittings and equipment  

  • Clothes lockers with bench  
  • Sanitary o Shower o Urinals  
  • WC  
  • Hand-wash basins  
  • Shoe racks  
  • Hand-towel dispensers  
  • Soap dispenser  
  • Mirrors  
  • Toilet-roll holders  
  • Laundry bag holders.  

Steriliser plant room

Function  

Service area of the sterilisers.  

Location and relationship  

Drawing 25: Steriliser plant room

Activities  

  • Maintenance and repair of autoclaves by trained technical staff  
  • Sampling facilities for steam and water quality  
  • Limited access to trained skilled maintenance personnel only.  

Requirements  

  • Technical personnel need to access the steriliser controls through the PPE room  
  • Waterproof, hardwearing floor, with a gradient in the direction of a floor drain  
  • Clearances as per specifications as steriliser manufacturers • Adequate space for maintenance and periodic testing is essential.    

Access to the maintenance area of the autoclaves must not interfere with the CSSD activities. For singledoor autoclaves, there must be no connecting door between the maintenance area and the sterilised supply store. The maintenance area in particular should be well ventilated by natural means assisted by mechanical extraction if necessary. Note that this only achievable with single door autoclaves. Where double door autoclaves are used care must be taken to identify an access point from within the unit, which causes least disruption.  

Fixtures, fittings and equipment  

As per manufacturer’s specifications.  

Services  

As per manufacturer’s specifications.

Building and Services